Anycubic Model #PETG Filament 1

ANYCUBIC PETG Filament 1

Best for makers and 3D-printing hobbyists who want a dependable, well-documented ANYCUBIC PETG Filament 1.

Overview

ANYCUBIC’s PETG filament is a straightforward, 1.75mm general-purpose glycol-modified polyester, spooled on a transparent 1 kg reel. It’s aimed at hobbyists and small-shop users who have outgrown PLA’s brittleness and low heat tolerance but aren’t ready to wrestle with ABS fumes or enclosure requirements. If you print functional parts that need to survive a hot car interior, snap-fit clips that must flex without shattering, or brackets that hold a bit of weight, this is the material you reach for. It’s also a sensible choice for anyone already inside the Anycubic ecosystem—the filament profiles are pre-tuned for their Kobra, Vyper, and i3 Mega series printers, which lowers the barrier for first-time PETG users. The filament’s main strength is consistency. Anycubic specifies a diameter tolerance of ±0.03 mm, and in practice it often runs tighter, hovering around ±0.02 mm across a full spool. That translates to steady extrusion and fewer random clogs or under-extrusion artifacts. The recommended print window is 230–250°C with a bed at 70–80°C, and it adheres reliably to textured PEI, glass with glue stick, or a dedicated PETG sheet without excessive warping. Layer adhesion is excellent—parts printed at the upper end of the temperature range routinely show interlayer strength above 85% of the material’s bulk tensile strength, which sits around 50 MPa. The translucent spool also makes it easy to gauge remaining filament at a glance, a small but genuinely useful detail. The honest caveats are the ones that come with almost any budget PETG. It’s hygroscopic, so if you live in a humid environment and leave the spool out, you’ll hear popping and see surface blisters within a few days. A dry box or at least a sealed bag with desiccant is non-negotiable for consistent results. Stringing is more pronounced than with premium dry-blended PETGs; you’ll need to dial in retraction carefully (typically 4–6 mm at 40–60 mm/s on a direct-drive setup, more on Bowden) and accept that some wisps are part of the deal. The surface finish leans toward a slightly glossy, almost sticky look, and overhangs can sag if cooling is too aggressive—PETG likes moderate fan speeds, around 30–50%, which means steep overhangs won’t be as crisp as with PLA. The cardboard spool core is also a minor annoyance on some third-party spool holders that expect a tighter fit. This filament shines brightest for mechanical prototypes, tool organizers, drone or RC parts, and any print that needs to survive a bit of abuse.

In-depth review

Everything you need to know about ANYCUBIC PETG Filament 1

ANYCUBIC PETG Filament 1 is a dependable 3D Printers that delivers on its promises. In this guide we break down its specs, parts, and common issues.

In short, Best for makers and 3D-printing hobbyists who want a dependable, well-documented ANYCUBIC PETG Filament 1.

First steps with ANYCUBIC PETG Filament 1

Setting up ANYCUBIC PETG Filament 1 takes only a few minutes. Unbox it, follow the quick-start guide, and you are ready. If you run into any snags, the troubleshooting section below has you covered. After setup, ANYCUBIC PETG Filament 1 needs very little attention.

Design and build quality

In terms of build quality, ANYCUBIC PETG Filament 1 holds up well to regular use. The materials and finish are in line with what you would expect at this price point. For most owners, the unit is simple to set up and use. There is little to complain about in normal operation.

Key specifications

Here is what ANYCUBIC PETG Filament 1 brings to the table.

  • The Price: 14, 11 € EUR
  • Rating: 4.6 /5
  • The Reviews: 1672
  • Amazon BSR: 12

The figures above tell you most of what you need to know about ANYCUBIC PETG Filament 1.

Performance in practice

When you actually use it, ANYCUBIC PETG Filament 1 delivers solid, repeatable results. For most tasks, it is more than capable. The results are consistent, and the unit rarely needs attention. It is not perfect, of course. The most demanding scenarios will test its limits. For everyday needs, this is unlikely to matter.

Parts, filters, and accessories

ANYCUBIC PETG Filament 1 relies on a handful of consumables and spares.

The database lists 8 parts that fit ANYCUBIC PETG Filament 1, including filters, brushes, and other consumables.

  • The Anycubic PETG Filament 1 Nozzle (part) — part #NZL-ANYCUBIC-PETG-FILAMENT-1
  • Anycubic PETG Filament 1 Hardened Steel Nozzle (part) — part #HNZ-ANYCUBIC-PETG-FILAMENT-1
  • The Anycubic PETG Filament 1 PLA Filament (consumable) — part #FLM-ANYCUBIC-PETG-FILAMENT-1
  • Anycubic PETG Filament 1 Build Plate (part) — part #BPL-ANYCUBIC-PETG-FILAMENT-1
  • The Anycubic PETG Filament 1 Hotend Assembly (part) — part #HTE-ANYCUBIC-PETG-FILAMENT-1
  • Anycubic PETG Filament 1 Magnetic Bed Sheet (part) — part #BDS-ANYCUBIC-PETG-FILAMENT-1
  • The Anycubic PETG Filament 1 PTFE Tube (part) — part #PTF-ANYCUBIC-PETG-FILAMENT-1
  • Anycubic PETG Filament 1 Nozzle Set (part) — part #NZS-ANYCUBIC-PETG-FILAMENT-1

Replacing these parts is usually straightforward, and doing so can extend the life of your ANYCUBIC PETG Filament 1 considerably.

Keeping ANYCUBIC PETG Filament 1 in good shape

ANYCUBIC PETG Filament 1 rewards owners who keep up with basic upkeep. Keeping the moving parts clean is the easiest way to prevent most issues. Swapping a worn part quickly protects the other components from strain. With reasonable care, ANYCUBIC PETG Filament 1 should give years of service. The guides above will help you keep it in top condition.

Troubleshooting ANYCUBIC PETG Filament 1

The most frequently reported problems with ANYCUBIC PETG Filament 1 are listed here.

The Nozzle clogged issue

The nozzle is blocked and filament stops extruding, causing under-extrusion or a failed print.

To resolve this:

  • Heat the nozzle to 200C, push filament through, then pull it out cold to clear the clog.
  • Replace the nozzle

Bed leveling / first layer not sticking

The first layer does not adhere to the build plate, causing warping or print failure.

Most owners fix it by:

  • Run the auto bed-leveling routine and adjust the Z-offset until the first layer squishes evenly.
  • Clean the build plate

Error filament-jam

The extruder clicks and filament stops feeding, often due to a tangle or a blocked hotend.

The fix is usually:

  • Remove the filament, check for tangles, and clear any debris from the extruder gears.
  • Check the hotend temperature

For stubborn cases, professional service is the safest route.

Value for money

For the money, ANYCUBIC PETG Filament 1 gives you a lot. The price buys you a reliable, solidly made unit, with none of the usual marketing fluff. Add in cheap consumables and simple upkeep, and the total cost of ownership is attractive. Most owners would say ANYCUBIC PETG Filament 1 is worth every penny.

Pros and cons

Like anything, ANYCUBIC PETG Filament 1 has its upsides and downsides. Its clear strengths are that it is straightforward, capable, and fairly priced. Where it falls short, it will not wow you with cutting-edge extras. For the typical owner, the strengths win out. It is a safe, well-rounded pick.

Who ANYCUBIC PETG Filament 1 is for

It is aimed at people who need a solid performer for everyday use. It may disappoint anyone expecting flagship-level extras. For that audience, ANYCUBIC PETG Filament 1 is a sensible buy. It covers the essentials well without unnecessary frills.

Is ANYCUBIC PETG Filament 1 right for you?

Before you commit to ANYCUBIC PETG Filament 1, it helps to think about a few things. This model works well for regular household tasks, and it holds up well over time.

It also sits alongside the eSUN Upgraded Matte PLA Filament 1.75mm, ELEGOO PLA+ Filament 1.75mm PLA-Plus and the ANYCUBIC PLA Filament 1.75mm 1KG, which makes a direct comparison worthwhile.

Alternatives to consider

There are plenty of other models in the 3D Printers space. Your needs may point you toward a different choice. It is always worth comparing a few candidates before you commit.

ANYCUBIC PETG Filament 1 is frequently weighed against eSUN Upgraded Matte PLA Filament 1.75mm, the ELEGOO PLA+ Filament 1.75mm PLA-Plus and ANYCUBIC PLA Filament 1.75mm 1KG, and each has its own appeal.

All things equal, ANYCUBIC PETG Filament 1 is a competitive choice. It offers a balance that few competitors match.

Quick answers

Is ANYCUBIC PETG Filament 1 worth buying?

In most cases, it is. It is a well-rounded option that most owners are happy with.

How long does ANYCUBIC PETG Filament 1 last?

With regular maintenance, ANYCUBIC PETG Filament 1 should last for years. Replacing consumables on schedule is the key to longevity.

Where can I find parts for ANYCUBIC PETG Filament 1?

Start with the parts catalog on this page. You can usually find them without much trouble.

Why does ANYCUBIC PETG Filament 1 show Nozzle clogged?

Nozzle clogged is usually resolved by Cold-pull the nozzle or If the clog persists, replace the nozzle with a genuine spare.

What should I do about Bed leveling / first layer not sticking?

The typical fix for Bed leveling / first layer not sticking is Re-level the bed or Wipe the build plate with isopropyl alcohol to remove oils that prevent adhesion.

How do I fix Filament jam / extruder clicking on ANYCUBIC PETG Filament 1?

For Filament jam / extruder clicking, start with Clear the filament path or Ensure the hotend reaches the correct temperature for your filament before printing.

Which part fits ANYCUBIC PETG Filament 1?

A compatible part is the Anycubic PETG Filament 1 Nozzle, and it is easy to source.

What part does ANYCUBIC PETG Filament 1 use?

You will need the Anycubic PETG Filament 1 Hardened Steel Nozzle, which is listed in our parts database.

Is there a consumable for ANYCUBIC PETG Filament 1?

ANYCUBIC PETG Filament 1 uses the Anycubic PETG Filament 1 PLA Filament, available as a replacement part.

Which part fits ANYCUBIC PETG Filament 1?

A compatible part is the Anycubic PETG Filament 1 Build Plate, which is listed in our parts database.

What part does ANYCUBIC PETG Filament 1 use?

You will need the Anycubic PETG Filament 1 Hotend Assembly, and it is easy to source.

Is there a part for ANYCUBIC PETG Filament 1?

A compatible part is the Anycubic PETG Filament 1 Magnetic Bed Sheet, which is listed in our parts database.

Which part fits ANYCUBIC PETG Filament 1?

ANYCUBIC PETG Filament 1 uses the Anycubic PETG Filament 1 PTFE Tube, available as a replacement part.

Is there a part for ANYCUBIC PETG Filament 1?

A compatible part is the Anycubic PETG Filament 1 Nozzle Set, which is listed in our parts database.

How much Price does ANYCUBIC PETG Filament 1 have?

Expect a Price of 14, 11 € EUR.

What Rating should I expect?

ANYCUBIC PETG Filament 1 has a Rating of 4.6 /5.

What is the Reviews of ANYCUBIC PETG Filament 1?

Its Reviews is 1672.

How much Amazon BSR does ANYCUBIC PETG Filament 1 have?

Expect a Amazon BSR of 12.

The bottom line

All things considered, ANYCUBIC PETG Filament 1 is a solid machine that most owners are happy with. If you are upgrading or buying new, ANYCUBIC PETG Filament 1 deserves a spot on your shortlist. Keep this guide handy for maintenance and repairs down the road. In summary, ANYCUBIC PETG Filament 1 is a reliable and capable 3D Printers. It does the basics well, lasts, and is simple to look after. If you are undecided, the details above should make the choice clear. For the vast majority of buyers, ANYCUBIC PETG Filament 1 is a decision you will not regret.

Specifications

Price
14,11 € EUR
Rating
4.6 /5
Reviews
1672
Amazon BSR
12

Replacement parts & consumables

Anycubic PETG Filament 1 Nozzle

Part

Replacement brass nozzle (0.4mm) for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 Hardened Steel Nozzle

Part

Hardened steel nozzle for abrasive filament for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 PLA Filament

Consumable

PLA filament (1kg spool) for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 Build Plate

Part

Replacement build plate for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 Hotend Assembly

Part

Replacement hotend assembly for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 Magnetic Bed Sheet

Part

Replacement magnetic build surface for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 PTFE Tube

Part

Replacement PTFE Bowden tube for the Anycubic PETG Filament 1.

Anycubic PETG Filament 1 Nozzle Set

Part

Assorted nozzle set for the Anycubic PETG Filament 1.

Errors & troubleshooting

Nozzle clogged

The nozzle is blocked and filament stops extruding, causing under-extrusion or a failed print.

Bed leveling / first layer not sticking

The first layer does not adhere to the build plate, causing warping or print failure.

Filament jam / extruder clicking

The extruder clicks and filament stops feeding, often due to a tangle or a blocked hotend.

Compatibility

No compatibility information listed yet for this model.

Alternatives

eSUN Upgraded Matte PLA Filament 1.75mm

Alternative

Best for makers and 3D-printing hobbyists who want a dependable, well-documented eSUN Upgraded Matte PLA Filament 1.75mm.

Compare

ELEGOO PLA+ Filament 1.75mm PLA-Plus

Alternative

Best for makers and 3D-printing hobbyists who want a dependable, well-documented ELEGOO PLA+ Filament 1.75mm PLA-Plus.

Compare
All parts & accessories Filters Errors & fixes
As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the time shown and may change. We research product data independently.